Automatic Transmission - 4L60-E/4L65-E for Chevrolet Impala 2005

All Component Locator

• Case Extension Identification
• Transmission Fluid Pan Identification

All Description and Operation

• Manual First Gear
• Manual Second Gear
• Manual Third Gear
• Neutral - Engine Running
• Overdrive Range, 3-2 Downshift
• Overdrive Range, 4-3 Downshift
• Overdrive Range, First Gear
• Overdrive Range, Fourth Gear - Torque Converter Clutch Applied
• Overdrive Range, Second Gear
• Overdrive Range, Third Gear
• Park - Engine Running
• Reverse

All Special Tools and Equipment

• Special Tools

Cleaning, Inspection, and Adjustment

• 2-4 Band Servo Piston Pin Length Check
• Case Assembly Inspection
• Clutch Air Check
• Forward Clutch Piston Travel Check
• Input Carrier Inspection
• Input Housing and Shaft Assembly Inspection
• Low and Reverse Clutch Spacer Plate Selection
• Reaction Gear and Carrier Inspection
• Reverse Input Clutch Plate Travel Check
• Torque Converter End Play Inspection

Disassembly, Overhaul, Repair, and Assembly

• 1-2 Accumulator Assemble
• 1-2 Accumulator Disassemble
• 1-2 Accumulator Installation
• 2-4 Band Installation
• 2-4 Band Servo 2nd Apply Piston Disassemble
• 2-4 Band Servo Piston Pin Length Check
• 2-4 Band, Input Clutches, Input Gear Set Removal
• 2-4 Servo Assembly Installation
• 2-4 Servo Cover and Assembly Removal
• 3-4 Accumulator Installation
• 3-4 Clutch Assemble
• 3rd Accumulator Retainer with Ball Assembly Leak Check
• 3rd Accumulator Retainer with Ball Replacement
• Case Bushing
• Case Extension Bushing Replacement
• Control Valve Body Assemble
• Control Valve Body Disassemble
• Converter Housing Removal
• Drain Oil
• Fluid Pump Rotor and Slide Measurement
• Forward Clutch Assembly Assemble
• Forward Clutch Sprag Assemble
• Forward Clutch Sprag Disassemble
• Holding Fixture Installation
• Holding Fixture Removal
• Inner Manual Linkage Removal
• Input Carrier Inspection and Installation
• Input Clutch Assembly Disassemble
• Input Housing and Shaft Assembly Assemble
• Input Housing to Output Shaft Seal Installation
• Input Sun Gear Bushing Replacement
• Internal Transmission Speed Sensor Rotor Replacement
• Low and Reverse Clutch Piston Installation
• Low and Reverse Clutch Piston Removal
• Low and Reverse Clutch Plate Installation
• Low and Reverse Clutch Support Disassemble
• Low and Reverse Clutch Support Installation
• Manual Detent Spring Installation
• Manual Shift Shaft Seal Installation
• Oil Filter Assembly Installation
• Oil Pump Body Bushing Replacement
• Oil Pump Cover and Body Assemble
• Oil Pump Cover Assemble
• Oil Pump Cover Disassemble
• Oil Pump Stator Shaft Bushing Replacement
• Output Shaft Installation
• Output Shaft, Reaction Gear, Low/Rev Clutch Removal
• Overrun Clutch Installation
• Reaction Carrier Shaft Replacement
• Reaction Gear and Carrier Installation
• Reaction Sun Gear Installation
• Reverse Input and 3-4 Clutch Housing Installation
• Reverse Input Clutch Assemble
• Reverse Input Clutch Bushing Replacement
• Reverse Input Clutch Disassemble
• Secondary Fluid Pump Assembly Installation
• Secondary Fluid Pump Assembly Removal
• Secondary Fluid Pump Filter Replacement
• Torque Converter Assembly Removal
• Torque Converter Installation
• Transmission Fluid Pan and Filter Assembly Removal
• Transmission Fluid Pan Installation
• Turbine Shaft O-Ring Installation
• Turbine Shaft O-Ring Removal

General Information

• Do Not Use Air Tools

Mechanical Specifications

• End Play Specifications
• Fastener Tightening Specifications
• Fluid Capacity Specifications

Other Specifications

• 2-4 Band Servo Piston Pin Selection
• Fluid Pump Rotor and Slide Measurement
• Forward Clutch Backing Plate Selection
• Low and Reverse Clutch Spacer Plate Selection
• Reverse Input Clutch Backing Plate Selection
• Secondary Fluid Pump Assembly Specifications
• Third and Fourth Clutch Backing Plate Selection
• Torque Converter End Play Inspection